Selection of titanium alloy tools for CNC machining

(1) It is easy to form a hard and brittle surface layer

Titanium alloys are highly chemically active. During high-temperature cutting, titanium absorbs N, O and other gases to form a hard and brittle surface layer. During the cutting process, the rake surface of the chip is in close contact with the rake surface before passing through the tool, forming a bonding layer (a); during the cutting process, a series of crescent dimples parallel to the cutting edge will be formed near the main cutting edge; in severe cases, , the tool material within a certain distance from the main cutting edge peels off, forming pits (b); due to the fluctuation of the cutting force, the tool tip collapses microscopically (c).

(2) Feed rate

Under the conditions of cutting speed 50m/min and depth of cut 1.0mm, when the feed rate is less than 0.13mm/r, the main cutting force Fz increases with the increase of feed rate. When the feed rate is 0.097mm/r , the feed resistance Fx is significantly reduced; when the feed amount is 0.084mm/r, the cutting depth resistance Fy is also significantly reduced. When the feed speed increases from 0.13mm/r , the fluctuation of cutting force weakens; due to the softening of workpiece material due to high cutting temperature, the change of feed resistance is particularly obvious when the feed resistance and depth of cut resistance decrease.

(3) High pressure and large flow cooling system

In order to effectively improve the productivity of equipment processing, extend the service life of equipment and tools, and improve the quality of parts processing, CNC machine tools for high-speed processing of structural parts made of difficult-to-machine materials such as titanium alloys are usually designed with high-pressure high-flow (HPHV) hydraulic cooling and lubrication systems. HPHV systems generally include a high-pressure cooling system (HPTC) directly through the spindle/tool, which injects external jets of cutting tools and workpieces through multiple external nozzles to maintain good spindle performance, rapidly cool the tool workpiece and flush chips, improving Improve the processing quality of parts and increase the service life of tools. High-efficiency high-speed CNC machine tools using HPHV cooling and lubrication systems require a pressure greater than 720psi (5MPa), and the commonly used industry standard is 1000-2000psi (7-14MPa). When the pressure is 1000psi, the flow rate is generally required to be not less than 30L/min.

( 4 ) Under the conditions of adding coolant for lubrication and wet cutting, the tool durability and processing efficiency can be improved. In order to reduce the cutting temperature, a large amount of cooling base cutting fluid should be poured into the cutting area. The thermal conductivity, specific heat, heat capacity, vaporization heat, vaporization speed, flow rate and flow rate requirements of cutting fluid are very high. Generally, the thermal conductivity of water is 3 to 5 times higher than that of oil, the specific heat is 1 times larger, and the heat of vaporization is about 10 times, so the water solubility and cooling performance are better. In CNC turning, milling and drilling, emulsions or aqueous solutions containing extreme pressure additives (including S, P and Cl) are often used. The formula of extreme pressure aqueous solution is: chlorinated fatty acid, polyvinyl chloride 0.5%~0.8%, trisodium phosphate 0.5%, triethanolamine 1%~2%, sodium nitrite 1.2%, and the rest is water.

(5) Equipment and manufacturing process are highly integrated

Using lower cutting speeds means longer machining cycles for titanium parts. Generally, the processing time of TC4 titanium alloy parts is 2 to 4 times that of ordinary steel parts, and 10 to 12 times that of typical aluminum alloy materials. However, the processing time of new titanium alloy material parts of Ti-5Al-5Mo-5V-3Cr and Ti-10V-2Fe-3Al is generally twice as long as that of TC4 titanium alloy material. This results in low productivity and high processing costs in the cutting of titanium alloy structural parts. Therefore, in order to improve the productivity of cutting titanium alloy parts, reduce processing costs, and adapt to large-scale customized production, many CNC machine tool manufacturers adopt palletized processing, or multi-spindle processing, or multi-table (region) processing, or turn-milling compound processing . and other manufacturing process technologies are integrated into high-efficiency and high-speed CNC processing machine tools for titanium alloy materials to improve processing productivity and reduce processing costs.

You Might Also Like

Send Inquiry